How to Start Lifting: Learn to Deadlift
/In the fourth video of the "How to Start Lifting" series, Phil and the Testify gang help you learn how to deadlift and also discuss how to go about your first deadlift workout.
(This video is a Blast from the Past video originally published on 10/25/21.)
At Testify, we offer small group training, private coaching (in-person or remotely via Zoom), online coaching, and form checks. Click the button below to get quality coaching from a Starting Strength Coach and start getting stronger TODAY.
Tips and Tricks for the New Lifter - Part II
/
Evan demonstrates a handy trick for loading and unloading your deadlift.
(This article is a Blast from the Past article originally posted on 04/16/21.)
In Part I of this series, we discussed several tips and tricks that might help you as a new lifter, and now, in Part II, we’re back with a few more:
Easy Loading for Deadlifts
When you’re loading (or unloading) your deadlift with more than one 45 lb plate per side or more than one bumper plate per side, roll the plate (on the side you’re currently loading) up onto a 2.5 lb plate. This will raise the 45 lb plate or bumper plate off the ground just enough that it makes it easier to slide on the next plate. Of course, using a deadlift jack is makes things even easier, and we have a video on how to make one (click here or scroll down to the end of this article), but in lieu of that, using a 2.5 lb plate works quite well.
Holding Valsalva for Multiple Reps
You can hold your Valsalva (i.e., your tightly held breath) for multiple reps on the bench press. Holding your Valsalva for 2-3 reps is pretty common on the bench press, and as long as you aren’t running out of oxygen, doing so works very well as you don’t have to get tight again before the next rep. Two warnings, though: first, don’t take it as a personal challenge to see how many reps you can get on one breath - this may not end well - and second, holding your Valsalva for multiple reps doesn’t usually work very well for lifts other than the bench press.
Evan shows how to easily remove multiple bumper plates at once.
Easy Unloading for Bumper Plates
If you’re finished snatching, cleaning, or deadlifting (even rowing), and you have multiple bumper plates on each side of the bar, here’s how to unload your bar: first, take the collars off both sides of the bar. Second, unload all of the plates from the left side of the bar. Third, raise the empty left side of the bar - walking it upward (the right side of the bar remains on the ground) until the bar is sitting vertically inside the stack of plates on the right side of the bar. Finally, simply lift the bar out of the stack, put the bar away, and then put the plates away.
We hope these tips help you in your training, and perhaps we’ll be back with a Part III in the future.
(Some links may be affiliate links. As an Amazon Associate, Testify earns from qualifying purchases.)
If you found this helpful, you’ll love our weekly email. It’s got useful videos, articles, and training tips just like the one in this article. Sign up below, and of course, if you don’t love it, you can unsubscribe at any time.
At Testify, we offer small group training, private coaching (in-person or remotely via Zoom), online coaching, and form checks. Click the button below to get quality coaching from a Starting Strength Coach and start getting stronger TODAY.
How to Start Lifting: Learn to Squat
/In the third video of the "How to Start Lifting" series, Phil and the Testify gang help you learn how to squat and also discuss how to go about your first squat workout.
(This video is a Blast from the Past video originally published on 10/18/21.)
At Testify, we offer small group training, private coaching (in-person or remotely via Zoom), online coaching, and form checks. Click the button below to get quality coaching from a Starting Strength Coach and start getting stronger TODAY.
How to Start Lifting | Personal Gear
/What personal gear do you need to start lifting weights? In the second video of the "How to Start Lifting" series, Phil covers the personal equipment that you'll need as well as a few things to avoid (spoiler: don't get Chuck Taylors!).
(This video is a Blast from the Past video originally published on 10/11/21.)
At Testify, we offer small group training, private coaching (in-person or remotely via Zoom), online coaching, and form checks. Click the button below to get quality coaching from a Starting Strength Coach and start getting stronger TODAY.
Tips and Tricks for the New Lifter
/
An additional use for your wrist wraps
(This article is a Blast from the Past article originally posted on 03/19/21.)
When you’re new to some task, like lifting, there are always a few tips and tricks that will seem rather obvious to you years later, so in an effort to speed things up a bit, here are several that might prove useful to you:
Deadlifting on a Non-level Floor
If you must deadlift on a slightly non-level floor (hopefully very slightly!), and you find that the barbell always wants to roll a bit, you can simply place your wrist wraps on the floor in front of the plates. You can, of course, use any other soft, thin items like socks, lifting straps, even sponges, but don’t use a hard item like a 2.5-lb plate. If you set the bar down, and it glances off that item, it will come back at your shins, and shins and horizontally moving barbells don’t get along well (hint: the barbell always wins). In addition, the contact between the plate(s) on the bar and the 2.5-lb plate on the floor may cause one or both of them to chip. Wrist wraps are thick enough to immobilize the bar but soft and compressible enough that setting the bar down on top of the wrist wraps won’t cause any problems.
Quit Using 2.5-lb Plates . . . Sometimes
Stop using 2.5-lb plates in your warm-ups. As you get stronger, you’ll find that you can round most - if not all - of your warm-up weights to numbers that end in “5.” This will allow you to stop using 2.5-lb plates in your warm-ups. If you’d like to use 2.5-lb plates in your final warm-up in an effort to be a bit more precise, that’s fine, but most of your warm-up weight selections won’t require this level of precision. (If your work sets on a given lift are less than 100 lbs, you might decide to use 2.5-lb plates more often in your warm-ups, but you can apply a similar exclusionary logic to the 1.25-lb plates instead.)
Stop Resting . . . Sort-of
Stop resting between your warm-ups sets. We mention this on a regular basis, but it still blows people’s minds that they don’t need to rest 5 minutes between every single set. Do your empty bar sets (alright, you can rest 15 seconds between your two empty bar sets of five reps), then add weight and go. Then add weight and go again. Repeat until it’s time for your first work set, before which you should probably rest a few minutes. Remember - the act of changing the weight on the bar gives you enough rest to do the next warm-up set. This will save you a lot of time in the gym.
Write Out Your Next Workout
Write out your next workout before leaving the gym. As you gain experience, you may ditch this habit, and that’s perfectly fine, but when you’re new, it’s a very productive use of your rest periods to start writing out your next workout in your training journal - especially the warm-ups. You’re already in “training mode,” and the warm-ups you performed today will inform and influence the warm-ups you do next time, so now is as good a time as any to write out your next training session (and you won’t have to think too hard when you come in the gym next time).
As always, we hope these tips and tricks help you get stronger and live better.
(Some links may be affiliate links. As an Amazon Associate, Testify earns from qualifying purchases.)